Home » Products » Dunlop Bond Coat

Dunlop Bond Coat

Dunlop Bond Coat is a water-based bonding coat that provides a chemical key to increase adhesion on smooth, dense, difficult non porous substrates prior to the application of Dunlop adhesives, floor levelling compounds and Dunlop undertile waterproofing membranes (in non-fully immersed situation).

Primer for non porous surfaces, smooth, dense substrates
Easy to use
Rapid drying
Tile over tile

Technical Data
Downloads

Use On

Internal sheet timber, fibre cement sheet, compressed fibre cement sheet, concrete, renders, screeds, masonry, AAC block, glazed tiles, Scyon.

Surfaces

Walls and floors

Location

Indoor and outdoor

Colour & Sizes

Size	Item Code
1L	32373

Coverage

Approximately 10m² per litre

Technical Datasheet

Safety Datasheet – Australia

Share this product

You might also need

Dunlop Ardit Feather Finish

A cement based smoothing compound designed to provide a smooth, permanent finish to a variety of internal substrates such as concrete, tiles, sheet timber (plywood & particleboard) and DUNLOP FLOOR LEVELLERS prior to the installation of floor coverings such as vinyl, carpet and ceramic tiles.

Dunlop Timber Floor Leveller

A high performance self-smoothing screed for timber floors that creates a smooth even finish prior to applying floor coverings.

Dunlop Construction Grout

Select the desired consistency
Area to be filled in m²

How to Calculate in m²:
Measure the width and the length in metres and multiply the width and the length together.
Application thickness (mm)

Guide for depth thicknesses:
The Dunlop Construction Grout can be used to achieve an application thickness of between 5mm to 100mm.
You will need
kgs
Disclaimer: Coverage will vary according to method of application, surface or substrate condition and on site conditions, the above is designed as a guide.

Dunlop Floor Repairer Rapid Patch

Area to be patched/ramped in m2

How to Calculate in m²:
Measure the width and the length in metres and multiply the width and the length together.
Application thickness (mm)

Guide for thickness:
The Dunlop Floor Repairer Rapid Patch can be used to patch from feather edge, 0mm to any thickness. Ideal for ramping from a feather edge to normal screed thicknesses - 15mm to 30mm.
You will need
kgs
Disclaimer: Coverage will vary according to method of application, surface or substrate condition and on site conditions, the above is designed as a guide.

Dunlop Ardit Rapidset Repair Mortar

Area to be patched/ramped in m²

How to Calculate in m²:
Measure the width and the length in metres and multiply the width and the length together.
Application thickness (mm)

Guide for thickness:
The Dunlop Rapidset Repair Mortar can be used to patch from feather edge to any thickness.
You will need
kgs
Disclaimer: Coverage will vary according to method of application, surface or substrate condition and on site conditions, the above is designed as a guide.

Dunlop Timber Floor Leveller

Area to be levelled in m²

How to Calculate in m²:
Measure the width and the length in metres and multiply the width and the length together.
Application thickness (mm)

Guide for thickness:
The Dunlop Timber Floor Leveller can level from 0-12mm without the addition of aggregate and 12-30mm with the addition of 2-5mm aggregate.
You will need
kgs
Disclaimer: Coverage will vary according to method of application, surface or substrate condition and on site conditions, the above is designed as a guide.

Dunlop Ardit Floor Leveller

Area to be levelled in m²

How to Calculate in m²:
Measure the width and the length in metres and multiply the width and the length together.
Application thickness (mm)

Guide for thickness:
The Dunlop Ardit Floor Leveller can level from 0-10mm without the addition of aggregate and 10-50mm with the addition of 2-5mm aggregate.
You will need
kgs
Disclaimer: Coverage will vary according to method of application, surface or substrate condition and on site conditions, the above is designed as a guide.

Dunlop Multipurpose Floor Leveller

Area to be levelled in m²

How to Calculate in m²:
Measure the width and the length in metres and multiply the width and the length together.
Application thickness (mm)

Guide for thickness:
The Dunlop Multipurpose Floor Leveller can level from 0-10mm without the addition of aggregate and 10-25mm with the addition of 2-5mm aggregate.
You will need
kgs
Disclaimer: Coverage will vary according to method of application, surface or substrate condition and on site conditions, the above is designed as a guide.

Dunlop Ultra-White Grout

Tile length in mm
mm
Tile width in mm
mm
Joint depth in mm
mm
Joint width in mm
mm
Area to be grouted in m²

How to Calculate in m²:
Measure the width and the length in metres and multiply the width and the length together.
Grout/m2 (no wastage allowed) kg/m²
Grout/m2 (with 15% wastage) kg/m²
You will need with 15% wastage
kgs
Disclaimer: Coverage will vary according to method of application, surface or substrate condition and on site conditions, the above is designed as a guide.

Dunlop Wide Joint Grout

Tile length in mm
mm
Tile width in mm
mm
Joint depth in mm
mm
Joint width in mm
mm
Area to be grouted in m²

How to Calculate in m²:
Measure the width and the length in metres and multiply the width and the length together.
Grout/m2 (no wastage allowed) kg/m2
Grout/m2 (with 15% wastage) kg/m2
You will need with 15% wastage
kgs
Disclaimer: Coverage will vary according to method of application, surface or substrate condition and on site conditions, the above is designed as a guide.

Dunlop Ready-to-Go Coloured Grout

Tile length in mm
mm
Tile width in mm
mm
Joint depth in mm
mm
Joint width in mm
mm
Area to be grouted in m²

How to Calculate in m²:
Measure the width and the length in metres and multiply the width and the length together.
Grout/m2 (no wastage allowed) kg/m²
Grout/m2 (with 15% wastage) kg/m²
You will need with 15% wastage
kgs
Disclaimer: Coverage will vary according to method of application, surface or substrate condition and on site conditions, the above is designed as a guide.

Dunlop Flexible Coloured Grout

Tile length in mm
mm
Tile width in mm
mm
Joint depth in mm
mm
Joint width in mm
mm
Area to be grouted in m²

How to Calculate in m²:
Measure the width and the length in metres and multiply the width and the length together.
Grout/m² (no wastage allowed) kg/m²
Grout/m² (with 15% wastage) kg/m²
You will need with 15% wastage
kgs
Disclaimer: Coverage will vary according to method of application, surface or substrate condition and on site conditions, the above is designed as a guide.

Dunlop Express Wet Area Waterproofing

Installation Type*
Choose area to be waterproofed
Area to be covered in m²

How to Calculate in m²:
Measure the width and the length in metres and multiply the width and the length together.
You will need (Standard Installation)
Ls
You will need (Rapid Installation)
Ls
Disclaimer: Coverage will vary according to method of application, surface or substrate condition and on site conditions, the above is designed as a guide.

Dunlop Damp-Proof Waterproofing

What level of damp-proofing is required?
Area to be waterproofed in m²

How to Calculate in m²:
Measure the width and the length in metres and multiply the width and the length together.
You will need
Ls
You will need
Ls
Disclaimer: Coverage will vary according to method of application, surface or substrate condition and on site conditions, the above is designed as a guide.

Dunlop Multipurpose Acrylic Render

Area to be rendered in m²

How to Calculate in m²:
Measure the width and the length in metres and multiply the width and the length together.
Application thickness (mm)

Guide for thickness:
The Dunlop Multipurpose Acrylic Render can be used to achieve an application thickness of between 2-10mm
You will need
kgs
Disclaimer: Coverage will vary according to method of application, surface or substrate condition and on site conditions, the above is designed as a guide.

Dunlop Multipurpose Fine Coat Render

Area to be rendered in m²

How to Calculate in m²:
Measure the width and the length in metres and multiply the width and the length together.
Application thickness (mm)

Guide for thickness:
The Dunlop Multipurpose Fine Coat Render can be used to achieve an application thickness of between 2-5mm
You will need
kgs
Disclaimer: Coverage will vary according to method of application, surface or substrate condition and on site conditions, the above is designed as a guide.

Dunlop Ready-to-Go Render

Area to be rendered in m²

How to Calculate in m²:
Measure the width and the length in metres and multiply the width and the length together.
Application thickness (mm)

Guide for thickness:
The Dunlop Ready-to-Go Render can be used to achieve an application thickness of between 1-5mm
You will need
kgs
Disclaimer: Coverage will vary according to method of application, surface or substrate condition and on site conditions, the above is designed as a guide.

Dunlop Primer & Additive

Select what you will be priming*
Area to be primed in m²

How to Calculate in m²:
Measure the width and the length in metres and multiply the width and the length together.
You will need
Ls
You will need
Ls
Disclaimer: Coverage will vary according to method of application, surface or substrate condition and on site conditions, the above is designed as a guide.